Denso GT10B-SB Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Barcodeleser Denso GT10B-SB herunter. Denso GT10B-SB User`s manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 144
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - User's Manual

Bar Code Handy Scanner GT10B-SB GT10B-LB User's Manual

Seite 2

iii To System Designers: • When introducing the scanner in those systems that could affect human lives (e.g., medicines management system), develo

Seite 3

83 RSS Scanning RSS-14, RSS-14 Truncated, RSS-14 Stacked, RSS-14 Stacked Omnidirectional Enable Disable (default) Scanning RSS Limited Enab

Seite 4 - DECLARATION OF CONFORMITY

84  Trigger switch control and magic key control Trigger switch control Auto-off mode 1 Auto-off mode 2 Momentary switching mode 1 (default)

Seite 5 - Contents

85 Scanner sensibility level in auto sensing mode High Medium (default) Low  Beeper, indicator LED and vibrator Beeper Enable (default)

Seite 6

86 Indicator LED Enable (default) Disable Vibrator OK vibrations (default) NG vibrations Disable  Data verification mode Data verif

Seite 7

87 Verification result output in data verification mode (Report of match/mismatch status) Disable transmission/Disable transmission (default)

Seite 8 - Preface

88 Number of characters to verify, starting from the verification start position 1 character 2 characters 3 characters 4 characters 5 char

Seite 9 - SAFETY PRECAUTIONS

89  Reading with scanner mounted on charger Enable Disable (default)

Seite 10

90 Chapter 14 Bar-Coded Parameter Menu for Bluetooth® Adapters (BA10-RKU) 14.1 Configuring the Bluetooth® Adapter from the Scanner The scanner ca

Seite 11

91 End of transfer After normal end of transfer of parameter settings, the scanner's indicator LED turns blue with one beep. If the parameter

Seite 12

92 14.2 Bar-Coded Parameter Menu for Bluetooth® Adapters  Starting and ending the setting procedure, and restoring to defaults Start setting

Seite 13

iv Handling the scanner Wrong handling of the scanner could result in a scanner failure, heat, or smoke. Be sure to observe the following. • If us

Seite 14

93  Bluetooth® interface communications parameters Clearing the transfer buffer when the Bluetooth® wireless link breaks Enable Disable (defa

Seite 15 - Components Required

94  USB keyboard interface communications parameters Caps mode (USB keyboard interface) Auto setting (default) Manual setting Caps Lock of

Seite 16 - Wireless Communication Link

95 Data transmission interval (USB keyboard interface) This parameter provides a choice of the following data transmission intervals that apply when

Seite 17 - Care and Maintenance

96  USB-COM interface communications parameters Monitoring CTS (USB-COM interface) Enable (default) Disable

Seite 18

97  RS-232C interface communications parameters Transmission speed (RS-232C interface) 1200 bps 2400 bps 4800 bps 9600 bps (default) 1440

Seite 19 - Interface

98 Stop bit (RS-232C interface) 1 bit (default) 2 bits Monitoring CTS (RS-232C interface) Enable (default) Disable

Seite 20 - Wireless Link

99  PS/2 keyboard interface communications parameters Keyboard connection type (PS/2 keyboard interface) With external keyboard (default) Wit

Seite 21

100 Data transmission interval (PS/2 keyboard interface) Select the data transmission interval that matches the computer's processing speed. Set

Seite 22 - address (in hexadecimal)

101 Chapter 15 Troubleshooting Problem 1: Bar code data not displayed on the computer screen correctly. Probable cause What to do: • The target Bl

Seite 23 - 2.4 Reestablishing Bluetooth

102 Problem 4: Scanner's operation period too short even after recharge. Probable cause What to do: • If fully discharging and then recharging

Seite 24 - Wireless Link Status

v Handling the AC adapter Wrong handling of the AC adapter could result in a failure, heat, or smoke. Be sure to observe the following. • Do not s

Seite 25

103 Appendix 1 Specifications Item GT10B-SB/GT10B-LB Bar code symbologies available EAN-13, EAN-8, UPC-A, UPC-E, UPC/EAN with add-on, Interleaved 2

Seite 26

104 Reading diagrams GT10B-SB Speed-priority scanning 0Module size Scan range (incl. right andleft margins) 0Scan distance 15.75"(4

Seite 27

105 Reading diagrams GT10B-LB Speed-priority scanning 7.87" (200)11.81" (300)Scan range (incl. right andleft margins) 3.94&quo

Seite 28

106 Appendix 2 Bar Code Sample Label 031323120786 UPC-A 4906906 4901567014010 UPC-E EAN-13 49400397 0440238 10 EAN-8 UPC-E with 2-

Seite 29 - Chapter 5 Scanning Control

107 121347 Code 128 11970 1234558 EAN-128 MSI 98765C9 (01)12345678901231 Plessey RSS-14 (01)12345678901231 (01)12345678901231 RSS-1

Seite 30 - 5.2 Software Control

108 Appendix 3 Bluetooth Glossary The table below lists Bluetooth terms used in this manual. Bluetooth Address (BD_ADDR) Bluetooth Device Addres

Seite 31

109 Appendix 4 Pairing (Device authentication) Pairing (or bonding) is the Bluetooth authentication process for confirming the device at the othe

Seite 32

110 Scanner response to pairing requests The following is the procedure for responding to a pairing request from a Bluetooth device to the scanner.

Seite 33

111 Appendix 5 Quick Setup for the Use of USB Keyboard Interface  Requirements Hardware USB-equipped computer Scanner GT10B-SB or GT10B-LB Blueto

Seite 34

112 (3) Press the SETUP button on the rear of the Bluetooth adapter for at least 0.5 second to switch it to Setup mode. The interface/power supp

Seite 35

vi Handling the scanner and AC adapter Wrong handling of the scanner or AC adapter could result in a failure, heat, or smoke. Be sure to observe th

Seite 36 - 7.1 Data Verification Mode

113 (8) Check that the USB keyboard is selected and then specify the keyboard type matching the usage environment. (9) On the file menu, choose

Seite 37

114 Appendix 6 Quick Setup for the Use of USB-COM Interface  Requirements Hardware USB-equipped computer Scanner GT10B-SB or GT10B-LB Bluetooth

Seite 38

115 (3) Press the SETUP button on the rear of the Bluetooth adapter for at least 0.5 second to switch it to Setup mode. The interface/power sup

Seite 39

116 (8) Specify the USB-COM as interface. (9) On the file menu, choose Apply new settings to switch the Bluetooth adapter's interface to t

Seite 40 - Output master data

117  Displaying data from scanner on computer The following is the procedure for displaying data from the USB-COM interface on the computer screen.

Seite 41 - Read, by Scanning Bar Codes

118 (4) Specify COM port. The USB-COM driver does not need this setting, so simply press the OK button. This completes HyperTerminal setup. (5)

Seite 42 - Chapter 8 Data Editing

119 Appendix 7 Quick Setup for the Use of RS-232C Interface  Requirements Hardware Computer supporting COM ports Scanner GT10B-SB or GT10B-LB Blu

Seite 43 - 8.2 Substituting Data

120 (3) Press the SETUP button on the rear of the Bluetooth adapter for at least 0.5 second to switch it to Setup mode. The interface/power supp

Seite 44 - 8.3 Blocksorting Data

121  Establishing a Bluetooth® wireless link between the scanner and the Bluetooth® adapter (1) Use the scanner to read the bar code printed on the

Seite 45 - (2) Comma

122 (3) Specify the connection configuration. Click the downward facing arrow to the right of the label "Connection configuration," sele

Seite 46 - 8.6 Data Editing Notes

vii • If you are not using the scanner for a long time, be sure to remove the battery cartridge for safety. Failure to do so could result in a fi

Seite 47

123 Appendix 8 Quick Setup for the Use of PS/2 Keyboard Interface  Requirements Hardware USB-equipped computer or computer supporting COM ports S

Seite 48

124  Changing Bluetooth® adapter's interface to PS/2 keyboard interface The default interface of the Bluetooth adapter is USB keyboard interfa

Seite 49

125  Establish a Bluetooth® wireless link between the scanner and the Bluetooth® adapter (1) Use the scanner to read the bar code printed on the ba

Seite 50

Bar Code Handy Scanner GT10B-SB GT10B-LB User's Manual First Edition, October 2004 Fourth Edition, Septembe

Seite 51

DENSO WAVE INCORPORATED 4-2-12, Toranomon, Minato-ku, Tokyo, Japan 105-0001 http://www.denso-wave.com/

Seite 52 - 9.1 Beeper

viii Components Required The scanner GT10B-SB/LB requires the following components that differ depending upon whether the Bluetooth® adapter is used

Seite 53 - (3) Beeper frequency

ix Bluetooth® Wireless Communication Link The scanner GT10B-SB/LB uses Bluetooth® wireless networking technology. Item Specifications Standard Blueto

Seite 54 - 9.2 Indicator LED

x Care and Maintenance Dust and other foreign matter on the clear plate of the reading window can impede bar code input, so regularly check for it an

Seite 55 - 9.3 Vibrator

1 Chapter 1 Part Names and Functions Reading windowPoint this at the bar code to read. Magic keyHolding down this key for approx. 2 se

Seite 56 - Chapter 10 Communication

2 Chapter 2 Bluetooth Interface For terms relating to Bluetooth wireless communication in this manual, refer to Appendix 3 "Bluetooth Glossa

Seite 57 - 10.2 Communication Format

 DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any

Seite 58

3 2.2 Establishing Bluetooth Wireless Link After enabling the Bluetooth interface, establish a Bluetooth wireless link between the scanner and the

Seite 59

4 3) Select an arbitrary version and press the OK button. 4) On the Bluetooth window shown below, select "Connect to optional Bluetooth dev

Seite 60

5 z When using a commercially available bar code generator, generate it in the following format. Bar code type Code 128, Code set A Value ADDR fo

Seite 61

6 2.3 Breaking Bluetooth Wireless Links Holding down the magic key in the regular read mode breaks the scanner's Bluetooth wireless link. Scan

Seite 62

7 2.5 Indication of Bluetooth Wireless Link Status The scanner's indicator LED and beeper together indicate the status of the scanner's B

Seite 63

8 Chapter 3 Reading Bar Codes (1) Press the trigger switch to turn on the illumination LED and prepare the scanner for reading. Note: This step

Seite 64 - Spare Number o

9  Reading RSS-14 Stacked and RSS-14 Stacked Omnidirectional symbols The scanner reads RSS-14 Stacked and RSS-14 Stacked Omnidirectional symbols in

Seite 65

10  Switching to sleep mode for power saving After completion of scanning, the scanner switches from standby to sleep mode to save power. The scanne

Seite 66

11 Chapter 4 Customizing the Scanner You can customize the scanner by modifying communications, bar code type, and other scanner parameters with t

Seite 67

12 Chapter 5 Scanning Control Two types of scanning controls are available—Trigger switch control and Software control. Trigger switch control: Pres

Seite 68

FCC and RSS-210 Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device co

Seite 69

13 5.2 Software Control You can control the scanner by sending scanning control commands from the host computer, instead of pressing the trigger swit

Seite 70

14 Failure read • Auto-off mode 1 • Momentary switching mode 1 (2) Continuous reading mode Switching to the ready-to-scan state with

Seite 71

15 5.3 Auto Sensing Mode—Automatic Detection of Labels In the auto sensing mode, bringing a code label within the scan range of the reading window t

Seite 72 - UPC-A/E, EAN-13/8

16 5.4 Reading with Scanner Mounted on Charger A setting enables read operation with the scanner mounted on the charger, drawing its power from the

Seite 73

17 Chapter 6 Magic Key Control Holding down the magic key breaks Bluetooth® wireless links. Note that, in the data verification mode, it cannot br

Seite 74

18 The following table lists the relationship between the magic key functions and trigger switch operating modes. (It applies to both the regular rea

Seite 75

19 Chapter 7 Scanning Functions 7.1 Data Verification Mode The data verification mode verifies the bar code data read against the master data store

Seite 76

20  2-point verification read After registration of master data, the scanner reads a bar code, verifies the bar code data read against the master da

Seite 77

21 7.1.2 Verification conditions You can specify a verification starting position and the number of characters to check. • Starting position: The ch

Seite 78 - (5) Data verification mode

22 7.1.3 Verification result output (1) Report of match/mismatch status You can select any of the following report types by using the bar-coded par

Seite 79

The radio frequency module that complies with the Directive 99/5/EC (R&TTE) is mounted on this device (GT10B-SB/LB). DECLARATION OF CONFORMITY Di

Seite 80

23 7.1.4 Output of the master data registered Scanning the "Output master data" bar code given below lets the scanner output the master da

Seite 81

24 7.2 Specifying the Numbers of Digits of Standard 2of5 and Interleaved 2of5 Symbols to Read, by Scanning Bar Codes You can specify the numbers of

Seite 82

25 Chapter 8 Data Editing The scanner can edit bar code data read in the format specified with the configuration software (ScannerSetting) and trans

Seite 83

26 (3) Extracting data from the specified start to tail positions The start position must be within the range from the 2nd to 99th digits. If the nu

Seite 84

27 (2) Transferring the substituted element string If the bar code data contains the specified substitution string within the specified search area,

Seite 85 - (15) For Bluetooth

28 8.4 Parenthesizing AIs (Application Identifier) in EAN-128 Data The scanner parenthesizes all AIs contained in EAN-128 data read and transfers th

Seite 86

29 (3) Tab (ASCII 09h <HT>) Specifying a tab as a delimiter outputs tab-delimited data. No tab follows the tail of the data. A header and term

Seite 87

30 (12) Conversions apply to Codabar start/stop characters and include them in the number of digits. (13) Conversions force Codabar start/stop char

Seite 88 - All defaults

31 AI Format Description 23n n3+n..19 Batch or Lot Number (Transitional Use) (**) 240 n3+an..30 Additional Product Identification Assigned by

Seite 89

32 AI Format Description 345n n4+n6 Width, Diameter, or 2nd Dimension, Feet, Logistics (***) 346n n4+n6 Width, Diameter, or 2nd Dimension, Ya

Seite 90

Contents Preface ...

Seite 91

33 AI Format Description 414 n3+n13 Identification of a Physical Location--EAN.UCC Global Location Number 415 n3+n13 EAN.UCC Global Location Numbe

Seite 92

34 AI Format Description 94 n2+an..30 Company Internal Information--Company 95 n2+an..30 Company Internal Information--Carrier 96 n2+an..30 Co

Seite 93

35 Chapter 9 Beeper, Indicator LED and Vibrator 9.1 Beeper (1) Beeping The scanner emits a short, long, one-shot, or intermittent beep to indicate

Seite 94

36 One-shot beep*2 (40 ms) or intermittent beep*2 (at 60 ms intervals) when: • either one of the 1st and 2nd rows of an RSS-14 Stacked or RSS-14 Stac

Seite 95

37 9.2 Indicator LED The indicator LED lights or flashes in blue, green, red or orange to indicate the scanner status as described below. Lights in b

Seite 96

38 The indicator LED can be disabled with the bar-coded parameter menu or configuration software (ScannerSetting). In any of the following cases, how

Seite 97

39 Chapter 10 Communication 10.1 Bluetooth Interface The bar-coded parameter menu and the configuration software (ScannerSetting) provide a choice

Seite 98

40 10.2 Communication Format 10.2.1 Data transmission format Select one of the following two data transmission formats. No. of digits Header Code ID

Seite 99

41 (3) Code ID mark This optional field specifies a code ID mark identifying a bar code symbology. Six types of system-defined code ID marks are ava

Seite 100

42 (4) Number of digits This optional field specifies the number of digits (2 or 4 digits) of bar code data to transmit or disables the transmission

Seite 101

8.6.2 Rules for data editing... 29

Seite 102

43 Codabar (NW-7) Start code Data C/D Stop code The Codabar symbology may or may not contain a check digit. You can select whether or not to check

Seite 103

44 10.2.2 GTIN Format Conversion If the GTIN format conversion function is enabled, EAN-13, EAN-8, UPC-A, UPC-E and Interleaved 2of5 (14-digit) code

Seite 104

45 10.3 Data Packaging (Packetizing) Data packaging is available to boost the reliability of data transfers over the Bluetooth wireless link from t

Seite 105

46 Using scanner connected to Bluetooth adapter Scanner settings: Data packaging mode (to BA10-RKU) Bluetooth adapter settings: GT10 series as ta

Seite 106 - Disable (default)

47 Example of analysis for packet received Data received (hexadecimal) 10H 02h 00h 13h 00h 00h 31h 32h 33h 34h 35h 36h 37h 38h 0Dh C4h 18h 10h 03h

Seite 107 - Adapters (BA10-RKU)

48 Chapter 11 Charging and Replacing the Battery Cartridge 11.1 Charging and Discharging the Battery Cartridge When the battery cartridge charge

Seite 108

49  Charging procedure (1) Connect the AC adapter to the charger and then plug it into an electrical outlet. Confirm that the green power supply

Seite 109 - Adapters

50 11.2 Replacing the Battery Cartridge The rechargeable battery cartridge is a consumable part with a finite service life. It is time to replace it

Seite 110 - Disable

51 (5) Connect a new battery cartridge to the battery cable connector. Note: Do not peel off the protection film covering a battery cartridge. (6)

Seite 111 - OFF (default)

52 11.3 Recycling the Battery Cartridge Battery Cartridge Recycling Request - This product uses a Nickel-metal hydride battery that contains scarce

Seite 112 - Numeric keypad

 Data verification mode ... 86

Seite 113 - Disable

53 Chapter 12 Parameters and Defaults The tables below list the parameters and their defaults. Those parameter settings can be changed with the ba

Seite 114

54 (2) Data transmission format and bar code symbologies Items Parameters Defaults Refer to: Enable Prefix transmission Disable  Enable Suffix

Seite 115 - 1 bit (default)

55 UPC-A/E, EAN-13/8 Items Parameters Defaults Refer to: Enable  Scanning UPC-A, UPC-E, EAN-13 and EAN-8 Disable Enable Scanning UPC/EAN with 2-

Seite 116

56 Standard 2of5 Items Parameters Defaults Refer to: Enable, without C/D Enable, with C/D Scanning Standard 2of5 Disable  Minimum number of di

Seite 117

57 Item Parameters Defaults Refer to: MOD-16  Check digit method for Codabar (NW-7) 7-check method Transmit a/b/c/d Transmit A/B/C/D Transmi

Seite 118 - Chapter 15 Troubleshooting

58 Code 128, EAN-128 Items Parameters Defaults Refer to: Enable  Scanning Code 128 Disable Enable  Scanning EAN-128 Disable Minimum number of

Seite 119

59 (3) Trigger switch control and magic key control Items Parameters Defaults Refer to: Auto-off mode 1 Auto-off mode 2 Momentary switching mode

Seite 120 - Appendix 1 Specifications

60 (4) Beeper, indicator LED and vibrator Items Parameters Defaults Refer to: Enable  Beeper Disable Section 9.1 Short (60 ms)  Medium (80 ms)

Seite 121

61 (5) Data verification mode Items Parameters Defaults Refer to: Regular read mode  Scanning modes Data verification mode 2-point verification

Seite 122

62 (7) Speed-/depth-priority scanning Items Parameters Defaults Refer to: Speed-priority scanning  Speed-/depth-priority scanning Depth-priority sc

Seite 123

i Preface This user's manual sets forth the procedures for handling, connecting, operating, and cleaning your bar code handy scanner. Before you

Seite 124

63 (9) For Bluetooth adapter: Bluetooth® communications parameters Items Parameters Defaults Refer to: Enable Clear the transfer buffer when the B

Seite 125 - Glossary

64 Items Parameters Defaults Refer to: Inboard numeric keys  Numeric key type Numeric keypad (See Note 6.) Enable Special key transmission Disa

Seite 126 - wireless link

65 (12) For Bluetooth adapter: USB-COM interface communications parameters The following settings take effect only when the USB-COM interface is set

Seite 127

66 (14) For Bluetooth adapter: PS/2 keyboard interface communications parameters The following settings take effect when the PS/2 keyboard interface

Seite 128 -  Requirements

67 Items Parameters Defaults Refer to: Enable Special key transmission Disable  (See Note 7.) (Note 7) Special key transmission applies to the f

Seite 129 - Bluetooth

68 (15) For Bluetooth adapter: Substitution of header/terminator for PS/2 and USB keyboard interfaces The following settings take effect only when t

Seite 130

69 Chapter 13 Bar-Coded Parameter Menu for Scanners 13.1 Parameter Setting Procedure Using the Bar-Coded Parameter Menu Start operation Scan t

Seite 131

70 13.2 Bar-Coded Parameter Menu for Scanners To set parameters given on this page, it is necessary to first scan the "Start operation" b

Seite 132

71  Starting/ending the setting procedure and reverting to defaults To set parameters given on the following pages, it is necessary to scan the &quo

Seite 133

72  Bluetooth® interface communications parameters Communications protocol Non-acknowledge mode (default) ACK/NAK mode Data packaging mode (t

Seite 134

ii SAFETY PRECAUTIONS Be sure to observe all these safety precautions.  Please READ through these instructions carefully. They will enable you to us

Seite 135

73 Timeout period for slave to wait for a connection request 2 minutes (default) 4 minutes 10 minutes 30 minutes Clearing the transfer bu

Seite 136

74  Data transmission format and bar code symbologies Transmission of code ID mark Enable Disable (default) Code ID mark position Before

Seite 137

75 UPC-A/-E and EAN-13/-8 Scanning UPC-A, UPC-E, EAN-13 and EAN-8 Enable (default) Disable Scanning UPC/EAN with Add-on Enable, no restrict

Seite 138

76 Transmission of padding characters "0" for the specified number of digits of UPC-E Enable Disable (default) Transmission of a che

Seite 139

77 Transmission format of EAN-8 (Conversion to EAN-13) Enable conversion Disable conversion (default) Transmission format of UPC-E (Conversion

Seite 140

78 Transmission of a check digit for Standard 2of5 Enable (default) Disable Specification of the number of digits for Standard 2of5, by bar co

Seite 141

79 Codabar (NW-7) Scanning Codabar (NW-7) Enable, without C/D (default) Enable, with C/D Disable Transmission of a check digit for Codabar (

Seite 142

80 Code 32 Conversion from Code 39 to Code 32 format Enable Disable (default) Transmission of leading "A" in Code 32 data Enable

Seite 143 - Bar Code Handy Scanner

81 Code 39 Scanning Code 39 Enable, without C/D (default) Enable, with C/D Disable Transmission of a check digit for Code 39 Enable (defa

Seite 144 - DENSO WAVE INCORPORATED

82 Code 128/EAN-128 Scanning Code 128 Enable (default) Disable Scanning EAN-128 Enable (default) Disable Transmission of FNC1 for Code

Kommentare zu diesen Handbüchern

Keine Kommentare